„Arduino 37 modules kit” változatai közötti eltérés

Innen: apaboard
Ugrás a navigációhoz Ugrás a kereséshez
Nincs szerkesztési összefoglaló
Nincs szerkesztési összefoglaló
40. sor: 40. sor:
== XY-a is joystick module  KY-023==
== XY-a is joystick module  KY-023==
== Metal touch sensor module  KY-036==
== Metal touch sensor module  KY-036==
== Pinmap ==
{| class="wikitable" border="1"
|-
! Item
! Picture
! Description
|-
| KY001:
Temperature Sensor Module
| [[File:KY001.png | 300px]]
|
This module measures the temperature and reports it through the 1-wire bus digitally to the Arduino.
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/DS18B20.pdf DS18B20]
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY001+code.pdf Arduino Sample Code]
|-
| KY002:
Shock Sensor Module
| [[File:KY002.png |  300px]]
|
This module is digital shock sensor. It will output a high level signal when it detects a shock event.
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY002+code.pdf Arduino Sample Code]
|-
| KY003:
Hall Magnetic Field Sensor Module
| [[File:KY003.png | 300px]]
|
This module can be used to detect the presence of an magnetic field. If there is an magnetic field present, it will report a high level signal.
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY003+code.pdf Arduino Sample Code]
|-
| KY004:
Momentary Button Module
| [[File:KY004.png | 300px]]
|
This is a button module. When the button is pressed, it will a high level signal.
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY004+code.pdf Arduino Sample Code]
|-
| KY005:
Infrared Transmitter Module
| [[File:KY005.png | 300px]]
|
This is an infrared transmitter module that is used to emit infrared signal.
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY005+code.pdf Arduino Sample Code]
|-
| KY006:
Buzzer Module
| [[File:KY006.png | 300px]]
|
This is an active buzzer module that can make different sound.
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY006+code.pdf Arduino Sample Code]
|-
| KY008:
Laser Diode Module
| [[File:KY008.png| 300px]]
|
This is a laser emitter diode. The working voltage is 5V, with a wavelength of 650nm.
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY008+code.pdf Arduino Sample Code]
|-
| KY009:
RGB three colors LEDs module
| [[File:ky009.jpg | 300px]]
|
This is a surface mount three-color LED module that can make any color we want by combing different intensities of Red, Blue and Green.
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY009+code.pdf Arduino Sample Code]
|-
| KY010:
Light Block Sensor Module
| [[File:KY010.png |300px]]
|
This is a light block sensor module, where there is an object in the middle of the U shape. The sensor will output a high level signal.
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY010+code.pdf Arduino Sample Code]
|-
| KY011:
Dual Light LEDs module
| [[File:ky011.jpg | 300px]]
|
This is a dual color LED module.
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY011+code.pdf Arduino Sample Code]
|-
| KY012:
Buzzer Module
| [[File:ky012.jpg | 250px]]
|
This is a nonactive buzzer module.
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY012+code.pdf Arduino Sample Code]
|-
| KY013:
Analog Temperature Sensor
| [[File:ky013.jpg | 250px]]
|
This is an analog temperature sensor that outputs it voltage in proportional to the temperature.
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY013+code.pdf Arduino Sample Code]
|-
| KY015:
Temprature and Humidity Sensor
| [[File:ky015.jpg | 250px]]
|
This DHT11 Temperature and Humidity Sensor features a calibrated digital signal output with the temperature and humidity sensor complex,ensureing the high reliability and excellent long-term stability. A high-performance 8-bit microcontroller is connected. This sensor includes a resistive element and a sense of wet NTC temperature measuring devices. It has excellent quality, fast response, anti-interference ability and high cost performance advantages.
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY015+code.pdf Arduino Sample Code]
|-
| KY016:
RGB three colors LED module
| [[File:ky016.jpg | 250px]]
|
This is a through the hole three-color LED module that can make any color we want by combing different intensities of Red, Blue and Green.
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY016+code.pdf Arduino Sample Code]
|-
| KY017:
Quicksilver Switch Module
| [[File:ky017.jpg | 250px]]
|
A tilt switch that can turn on and off depending on the tilt position. The switch is mercury.
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY017+code.pdf Arduino Sample Code]
|-
| KY018:
Optosensor Module
| [[File:ky018.jpg | 250px]]
|
Photoresistors are semiconductor photosensitive devices, in addition to having high sensitivity, fast response, consistent with the spectral characteristics and value of good features
Under a high temperature, and humidity in harsh environments, it also can maintain a high degree of stability and reliability
Wide pan used cameras, solar garden lights, lawn, detectors, clock, music, cups, gift boxes, mini-night light, light voice switches, lights automatically switch toys and a variety of light control, light control lighting, lamps and other light automatic opening control field
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY018+code.pdf Arduino Sample Code]
|-
| KY019:
5V DC Relay Module
| [[File:ky019.jpg | 250px]]
|
This is 1 channel relay module with the following spec:
*Can be used as microcontroller development board module can be used as home appliance control
*5 V-12V to TTL control signal
*The control signal DC or AC, 220V AC load can be controlled.
*There is a normally open and one normally closed contact
*A power indicator light
*A control indicator, pull off, disconnect does not shine
*Aransistor drive to increase the relay coil control pins high impedance.
*A control pin has a pull-down circuit to prevent malfunction relay vacant
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY019+code.pdf Arduino Sample Code]
|-
| KY020:
Tilt Switch Module
| [[File:ky020.jpg | 250px]]
|
Tilt switch module and a digital interface, built-in 13 LED build a simple circuit to produce tilt warning lamp 13 comes with digital interfaces of the LED, the tilt switch sensor interface to access digital 3,when the tilt open Off sensor senses a key signal, LED lights, otherwise off.
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY020+code.pdf Arduino Sample Code]
|-
| KY021:
Mini Reed Switch Module
| [[File:ky021.jpg | 250px]]
|
Reed module and the interface comes with digital 13 LED build a simple circuit to produce a Reed warning lamp 13 comes with digital interfaces of the LED, the Reed sensor access number 3 interface, when Reed sensors Sensed a key signal, LED lights, otherwise off.
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY020+code.pdf Arduino Sample Code]
|-
| KY022:
Infrared Receiver Module
| [[File:ky022.jpg | 300px]]
|
This is the infrared receiver module, with the following features:
*The infrared receiver module is 1838 Infrared receiver
*Acceptance angle: 90 °,
*Operating voltage: 7-5.5V.
*Frequency: 37.9KHZ,
*Receiving distance: 18Meter.
*Using inside and outside the double-shielded package structure
*Anti-light, electromagnetic interference capability, built-in infrared dedicated IC Can in 500 LUX Light  intensity  to work properly.
*Widely used in: stereo, TV, VCR, disc players, set-top boxes, digital photo frame, car audio, remote control toys, satellite receiver, hard disk player, air conditioners, heaters, fans, lighting and other household appliances.
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/InfraredReceiver.rar Arduino Sample Code]
|-
| KY023:
Mini Dual Axis JoyStick
| [[File:ky023.jpg | 300px]]
|
On the principle, the control rod can be considered that it is organized  by the two potentiometer and a button.When using, it can connect with Arduino sensor shield,and connect Arduino corresponding pins through Arduino sensor cables.  It as the following spec:
*Directional movements are simply two potentiometers - one for each axis
*Compatible with Arduino interface
*The biaxial XY Joystick Module KY-023 applies ARDUINO
*Dimensions: 1.57 in x 1.02 in x 1.26 in (4.0 cm x 2.6 cm x 3.2 cm)
*5 Pin
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY023+code.pdf Arduino Sample Code]
|-
| KY024:
Linear magnetic Hall sensor
| [[File:ky024.jpg | 300px]]
|
Linear Hall magnetic module and a digital interface, built-in 13 LED build a simple circuit to
produce a magnetic field warning lamp 13 comes with digital interfaces of the LED, the linear Hall sensor magnetometer access number 3 interface, when linear Hall magnetometer Sensor senses a key signal, LED lights, otherwise off.
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY020+code.pdf Arduino Sample Code]
|-
| KY025:
Big Reed Switch Module
| [[File:ky025.jpg | 300px]]
|
Reed module and the interface comes with digital 13 LED build a simple circuit to produce a Reed warning lamp 13 comes with digital interfaces of the LED, the Reed sensor access number 3 interface, when Reed sensors Sensed a key signal, LED lights, otherwise off.
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY020+code.pdf Arduino Sample Code]
|-
| KY026:
Flame Sensor Module
| [[File:ky026.jpg | 300px]]
|
Sensor for flame wavelengths between 760 nm to 1100 nm infrared is most sensitive
*60 degree detection sensor
*Two outputs mode:
** AO: analog output- real-time output voltage signal on the thermal resistance
** DO: when the temperature reaches a certain threshold- the output high and low signal threshold adjustable via potentiometer
*Working voltage: DC 3V - 5.5V
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY020+code.pdf Arduino Sample Code]
|-
| KY027:
Magic LED cup Module
| [[File:ky027.jpg | 300px]]
|
This module has two parts - an LED and a mercury tilt switch. Pins are 1 G (ground), 2 + (5V power), 3 S signal and 4 L (LED.)
If you wired up 1 & 2 to power, pin 3 (signal) will alternate between 5V (HIGH) and 0V (LOW) as you tilt the module. If you connect a current limiting resistor to L2, you can use it as a blinking LED.
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY027+code.pdf Arduino Sample Code]
|-
| KY028:
Digital Temprateure Sensor Module
| [[File:ky028.jpg | 300px]]
|
Digital temperature module and a digital interface, built-in 13 LED build a simple circuit, making the temperature warning lamp 13 comes with digital interfaces of the LED, the digital temperature sensor connected digital three interfaces, when the digital temperature sensor senses a key signal, LED lights, otherwise off.
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY020+code.pdf Arduino Sample Code]
|-
| KY031:
Shock Sensor Module
| [[File:ky031.jpg | 300px]]
|
Knock sensor module and a digital interface, built-in LED build a simple circuit to produce
percussion flasher.
Interface comes with digital LED, will knock sensor connected digital 3 interface, when
percussion sensor senses measure to percussive signals, LED flashing light.
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY031+code.pdf Arduino Sample Code]
|-
| KY032:
Obstacle Sensor Module
|[[File:ky032.jpg | 300px]]
|
Obstacle avoidance sensor module KY-032 for Arduino:
With 4 pins, use an infrared beam to detect proximity of obstacles.
The potentiometers can be used to adjust sensitivity.
Pin 1 is Ground, pin 2 is 5V power, pin 3 is digital output (on/off depending on the beam), 4 is enabling.
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY031+code.pdf Arduino Sample Code]
|-
| KY033:
Line follow Sensor Module
| [[File:ky033.jpg | 300px]]
|
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY031+code.pdf Arduino Sample Code]
|-
| KY034:
7 Colors LED Blinking Module
| [[File:ky034.jpg | 300px]]
|
Automatic flashing colorful LED module KY-034 for Arduino:
*7 color flashing LED module automatically uses 5mm round high-brightness light-emitting diode which has the following characteristics:
*Shape: Round LED 5mm DIP type
*Working voltage: DC 3.0V - 4.5V
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY034+code.pdf Arduino Sample Code]
|-
| KY035:
Hall Sensor Module
| [[File:ky035.jpg | 300px]]
|
Analog magnetic sensor module and a digital interface, built-in 13 LED build a simple circuit to produce a magnetic flash
Makers.13 comes with digital interfaces of the LED, the analog magnetic sensor connected to the power board analog 5 ARDUINO Interfaces, when analog magnetic sensor to a signal, LED lights,otherwise the lights out.
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY031+code.pdf Arduino Sample Code]
|-
| KY036:
Metal Touch Sensor Module
| [[File:ky036.jpg | 300px]]
|
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY031+code.pdf Arduino Sample Code]
|-
| KY037:
High Sensitive Microphone Module
| [[File:ky037.jpg | 300px]]
|
For sound detection module has two outputs:
*AO, analog output, real-time output voltage signal of the microphone
*DO, when the sound intensity reaches a certain threshold, the output high and low signal
Module features:
*There is a mounting screw hole 3mm
*Use 5v DC power supply
*with analog output
*there are threshold level output flip
*high sensitive microphone and high sensitivity.
*a power indicator light
*the comparator output is light
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY031+code.pdf Arduino Sample Code]
|-
| KY038:
Microphone Module
| [[File:KY038.png| 300px]]
|
Microphone sound sensor module KY-038 for Arduino:
*LM393 main chip
*Electric condenser microphone
*Features Single channel signal output
*Low level output signal used for sound control light
*Great module for sound alarm system
*Working voltage: DC 4-6V
*Interface definition:
**AO: analog output sensor
**GND: ground
**VCC: Power supply input range: 3V-24V.
**DO: Digital Output (comparator output)
*Two red LED indication: POWER and SENSOR. POWER: Power is off. SENSOR: When the microphone senses sound reaches a certain value, this LED light.
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY031+code.pdf Arduino Sample Code]
|-
| KY039:
Heatbeat Sensor Module
| [[File:ky039.jpg | 300px]]
|
This project uses bright infrared (IR) LED and a phototransistor to detect the pulse of the finger, a red LED flashes with each pulse.
Pulse monitor works as follows: The LED is the light side of the finger, and phototransistor on the other side of the finger, phototransistor used to obtain the flux emitted, when the blood pressure pulse by the finger when the resistance of the phototransistor will be slight changed.
We chose a very high resistance resistor R1, because most of the light through the finger is absorbed,it is desirable phototransistor sensitive enough.Resistance can be selected by experiment to get the best results.
The most important is to keep the shield stray light into the phototransistor. For home lighting that is particularly important because the lights at home mostly based 50HZ or 60HZ fluctuate, so faint heartbeat will add considerable noise.
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY039+code.pdf Arduino Sample Code]
|-
| KY040:
Rotation Encoder Module
|[[File:KY040.png| 300px]]
|
By rotating the rotary encoder can be counted in the positive direction and the reverse direction during rotation of the output pulse frequency, unlike rotary potentiometer counter, which species rotation counts are not limited. With the buttons on the rotary encoder can be reset to its initial state, that starts counting from 0.
How it works: incremental encoder is a displacement of the rotary pulse signal is converted to a series of digital rotary sensors. These pulses are used to control angular displacement. In Eltra angular displacement encoder conversion using a photoelectric scanning principle. Reading system of alternating light transmitting window and the window is not consisting of radial indexing plate (code wheel) rotating basis, while being an infrared light source vertical irradiation light to the code disk image onto the receiving on the surface. Receiver is covered with a diffraction grating, which has the same code disk window width. The receiver's job is to feel the rotation of the disc resulting changes, and change the light into corresponding electrical changes. Then the low-level signals up to a higher level, and generates no interference square pulse, which must be processed by electronic circuits. Reading systems typically employ a differential manner, about the same but the phase difference of the two waveforms different by 180°compared to the signal in order to improve the quality and stability of the output signal. Reading is then the difference between the two signals formed on the basis,thus eliminating the interference.
*[https://s3.amazonaws.com/linksprite/Arduino_kits/advanced_sensors_kit/KY040+code.pdf Arduino Sample Code]
|}

A lap 2017. május 2., 20:17-kori változata

Small passive buzzer module KY-006

2-color LED module KY-011

Hit sensor module KY-031

Vibration switch module KY-002

Photo resistor module KY-018

Key switch module KY-004

Tilt switch module KY-020

3-color full-color LED SMD modules KY-009

Infrared emission sensor module KY-005

3-color LED module KY-016

Mercury open optical module KY-017

Yin Yi 2-color LED module 3MM KY-029

Active buzzer module KY-012

Temperature sensor module KY-013

Automatic flashing colorful LED module KY-034

Mini magnetic reed modules KY-021

Hall magnetic sensor module KY-003

Infrared sensor receiver module KY-022

Class Bihor magnetic sensor KY-035

Magic light cup module KY-027

Rotary encoder module KY-040

Optical broken module KY-010

Detect the heartbeat module KY-039

Reed module KY-025

Obstacle avoidance sensor module KY-032

Hunt sensor module KY-033

Microphone sound sensor module KY-038

Laser sensor module KY-008

5V relay module KY-019

Temperature sensor module KY-001

Temperature sensor module KY-028

Linear magnetic Hall sensors KY-024

Flame sensor module KY-026

Sensitive microphone sensor module KY-037

Temperature and humidity sensor module KY-015

XY-a is joystick module KY-023

Metal touch sensor module KY-036

Pinmap

Item Picture Description
KY001:

Temperature Sensor Module

Fájl:KY001.png

This module measures the temperature and reports it through the 1-wire bus digitally to the Arduino.

KY002:

Shock Sensor Module

Fájl:KY002.png

This module is digital shock sensor. It will output a high level signal when it detects a shock event.

KY003:

Hall Magnetic Field Sensor Module

Fájl:KY003.png

This module can be used to detect the presence of an magnetic field. If there is an magnetic field present, it will report a high level signal.

KY004:

Momentary Button Module

Fájl:KY004.png

This is a button module. When the button is pressed, it will a high level signal.

KY005:

Infrared Transmitter Module

Fájl:KY005.png

This is an infrared transmitter module that is used to emit infrared signal.

KY006:

Buzzer Module

Fájl:KY006.png

This is an active buzzer module that can make different sound.

KY008:

Laser Diode Module

Fájl:KY008.png

This is a laser emitter diode. The working voltage is 5V, with a wavelength of 650nm.

KY009:

RGB three colors LEDs module

Fájl:Ky009.jpg

This is a surface mount three-color LED module that can make any color we want by combing different intensities of Red, Blue and Green.

KY010:

Light Block Sensor Module

Fájl:KY010.png

This is a light block sensor module, where there is an object in the middle of the U shape. The sensor will output a high level signal.

KY011:

Dual Light LEDs module

Fájl:Ky011.jpg

This is a dual color LED module.

KY012:

Buzzer Module

Fájl:Ky012.jpg

This is a nonactive buzzer module.

KY013:

Analog Temperature Sensor

Fájl:Ky013.jpg

This is an analog temperature sensor that outputs it voltage in proportional to the temperature.

KY015:

Temprature and Humidity Sensor

Fájl:Ky015.jpg

This DHT11 Temperature and Humidity Sensor features a calibrated digital signal output with the temperature and humidity sensor complex,ensureing the high reliability and excellent long-term stability. A high-performance 8-bit microcontroller is connected. This sensor includes a resistive element and a sense of wet NTC temperature measuring devices. It has excellent quality, fast response, anti-interference ability and high cost performance advantages.

KY016:

RGB three colors LED module

Fájl:Ky016.jpg

This is a through the hole three-color LED module that can make any color we want by combing different intensities of Red, Blue and Green.

KY017:

Quicksilver Switch Module

Fájl:Ky017.jpg

A tilt switch that can turn on and off depending on the tilt position. The switch is mercury.

KY018:

Optosensor Module

Fájl:Ky018.jpg

Photoresistors are semiconductor photosensitive devices, in addition to having high sensitivity, fast response, consistent with the spectral characteristics and value of good features Under a high temperature, and humidity in harsh environments, it also can maintain a high degree of stability and reliability Wide pan used cameras, solar garden lights, lawn, detectors, clock, music, cups, gift boxes, mini-night light, light voice switches, lights automatically switch toys and a variety of light control, light control lighting, lamps and other light automatic opening control field

KY019:

5V DC Relay Module

Fájl:Ky019.jpg

This is 1 channel relay module with the following spec:

  • Can be used as microcontroller development board module can be used as home appliance control
  • 5 V-12V to TTL control signal
  • The control signal DC or AC, 220V AC load can be controlled.
  • There is a normally open and one normally closed contact
  • A power indicator light
  • A control indicator, pull off, disconnect does not shine
  • Aransistor drive to increase the relay coil control pins high impedance.
  • A control pin has a pull-down circuit to prevent malfunction relay vacant
KY020:

Tilt Switch Module

Fájl:Ky020.jpg

Tilt switch module and a digital interface, built-in 13 LED build a simple circuit to produce tilt warning lamp 13 comes with digital interfaces of the LED, the tilt switch sensor interface to access digital 3,when the tilt open Off sensor senses a key signal, LED lights, otherwise off.

KY021:

Mini Reed Switch Module

Fájl:Ky021.jpg

Reed module and the interface comes with digital 13 LED build a simple circuit to produce a Reed warning lamp 13 comes with digital interfaces of the LED, the Reed sensor access number 3 interface, when Reed sensors Sensed a key signal, LED lights, otherwise off.

KY022:

Infrared Receiver Module

Fájl:Ky022.jpg

This is the infrared receiver module, with the following features:

  • The infrared receiver module is 1838 Infrared receiver
  • Acceptance angle: 90 °,
  • Operating voltage: 7-5.5V.
  • Frequency: 37.9KHZ,
  • Receiving distance: 18Meter.
  • Using inside and outside the double-shielded package structure
  • Anti-light, electromagnetic interference capability, built-in infrared dedicated IC Can in 500 LUX Light intensity to work properly.
  • Widely used in: stereo, TV, VCR, disc players, set-top boxes, digital photo frame, car audio, remote control toys, satellite receiver, hard disk player, air conditioners, heaters, fans, lighting and other household appliances.
KY023:

Mini Dual Axis JoyStick

Fájl:Ky023.jpg

On the principle, the control rod can be considered that it is organized by the two potentiometer and a button.When using, it can connect with Arduino sensor shield,and connect Arduino corresponding pins through Arduino sensor cables. It as the following spec:

  • Directional movements are simply two potentiometers - one for each axis
  • Compatible with Arduino interface
  • The biaxial XY Joystick Module KY-023 applies ARDUINO
  • Dimensions: 1.57 in x 1.02 in x 1.26 in (4.0 cm x 2.6 cm x 3.2 cm)
  • 5 Pin
  • Arduino Sample Code
KY024:

Linear magnetic Hall sensor

Fájl:Ky024.jpg

Linear Hall magnetic module and a digital interface, built-in 13 LED build a simple circuit to produce a magnetic field warning lamp 13 comes with digital interfaces of the LED, the linear Hall sensor magnetometer access number 3 interface, when linear Hall magnetometer Sensor senses a key signal, LED lights, otherwise off.

KY025:

Big Reed Switch Module

Fájl:Ky025.jpg

Reed module and the interface comes with digital 13 LED build a simple circuit to produce a Reed warning lamp 13 comes with digital interfaces of the LED, the Reed sensor access number 3 interface, when Reed sensors Sensed a key signal, LED lights, otherwise off.

KY026:

Flame Sensor Module

Fájl:Ky026.jpg

Sensor for flame wavelengths between 760 nm to 1100 nm infrared is most sensitive

  • 60 degree detection sensor
  • Two outputs mode:
    • AO: analog output- real-time output voltage signal on the thermal resistance
    • DO: when the temperature reaches a certain threshold- the output high and low signal threshold adjustable via potentiometer
  • Working voltage: DC 3V - 5.5V
  • Arduino Sample Code
KY027:

Magic LED cup Module

Fájl:Ky027.jpg

This module has two parts - an LED and a mercury tilt switch. Pins are 1 G (ground), 2 + (5V power), 3 S signal and 4 L (LED.) If you wired up 1 & 2 to power, pin 3 (signal) will alternate between 5V (HIGH) and 0V (LOW) as you tilt the module. If you connect a current limiting resistor to L2, you can use it as a blinking LED.

KY028:

Digital Temprateure Sensor Module

Fájl:Ky028.jpg

Digital temperature module and a digital interface, built-in 13 LED build a simple circuit, making the temperature warning lamp 13 comes with digital interfaces of the LED, the digital temperature sensor connected digital three interfaces, when the digital temperature sensor senses a key signal, LED lights, otherwise off.

KY031:

Shock Sensor Module

Fájl:Ky031.jpg

Knock sensor module and a digital interface, built-in LED build a simple circuit to produce percussion flasher. Interface comes with digital LED, will knock sensor connected digital 3 interface, when percussion sensor senses measure to percussive signals, LED flashing light.

KY032:

Obstacle Sensor Module

Fájl:Ky032.jpg

Obstacle avoidance sensor module KY-032 for Arduino: With 4 pins, use an infrared beam to detect proximity of obstacles. The potentiometers can be used to adjust sensitivity. Pin 1 is Ground, pin 2 is 5V power, pin 3 is digital output (on/off depending on the beam), 4 is enabling.

KY033:

Line follow Sensor Module

Fájl:Ky033.jpg
KY034:

7 Colors LED Blinking Module

Fájl:Ky034.jpg

Automatic flashing colorful LED module KY-034 for Arduino:

  • 7 color flashing LED module automatically uses 5mm round high-brightness light-emitting diode which has the following characteristics:
  • Shape: Round LED 5mm DIP type
  • Working voltage: DC 3.0V - 4.5V
KY035:

Hall Sensor Module

Fájl:Ky035.jpg

Analog magnetic sensor module and a digital interface, built-in 13 LED build a simple circuit to produce a magnetic flash Makers.13 comes with digital interfaces of the LED, the analog magnetic sensor connected to the power board analog 5 ARDUINO Interfaces, when analog magnetic sensor to a signal, LED lights,otherwise the lights out.

KY036:

Metal Touch Sensor Module

Fájl:Ky036.jpg
KY037:

High Sensitive Microphone Module

Fájl:Ky037.jpg

For sound detection module has two outputs:

  • AO, analog output, real-time output voltage signal of the microphone
  • DO, when the sound intensity reaches a certain threshold, the output high and low signal

Module features:

  • There is a mounting screw hole 3mm
  • Use 5v DC power supply
  • with analog output
  • there are threshold level output flip
  • high sensitive microphone and high sensitivity.
  • a power indicator light
  • the comparator output is light
  • Arduino Sample Code
KY038:

Microphone Module

Fájl:KY038.png

Microphone sound sensor module KY-038 for Arduino:

  • LM393 main chip
  • Electric condenser microphone
  • Features Single channel signal output
  • Low level output signal used for sound control light
  • Great module for sound alarm system
  • Working voltage: DC 4-6V
  • Interface definition:
    • AO: analog output sensor
    • GND: ground
    • VCC: Power supply input range: 3V-24V.
    • DO: Digital Output (comparator output)
  • Two red LED indication: POWER and SENSOR. POWER: Power is off. SENSOR: When the microphone senses sound reaches a certain value, this LED light.
  • Arduino Sample Code
KY039:

Heatbeat Sensor Module

Fájl:Ky039.jpg

This project uses bright infrared (IR) LED and a phototransistor to detect the pulse of the finger, a red LED flashes with each pulse. Pulse monitor works as follows: The LED is the light side of the finger, and phototransistor on the other side of the finger, phototransistor used to obtain the flux emitted, when the blood pressure pulse by the finger when the resistance of the phototransistor will be slight changed.

We chose a very high resistance resistor R1, because most of the light through the finger is absorbed,it is desirable phototransistor sensitive enough.Resistance can be selected by experiment to get the best results. The most important is to keep the shield stray light into the phototransistor. For home lighting that is particularly important because the lights at home mostly based 50HZ or 60HZ fluctuate, so faint heartbeat will add considerable noise.

KY040:

Rotation Encoder Module

Fájl:KY040.png

By rotating the rotary encoder can be counted in the positive direction and the reverse direction during rotation of the output pulse frequency, unlike rotary potentiometer counter, which species rotation counts are not limited. With the buttons on the rotary encoder can be reset to its initial state, that starts counting from 0.

How it works: incremental encoder is a displacement of the rotary pulse signal is converted to a series of digital rotary sensors. These pulses are used to control angular displacement. In Eltra angular displacement encoder conversion using a photoelectric scanning principle. Reading system of alternating light transmitting window and the window is not consisting of radial indexing plate (code wheel) rotating basis, while being an infrared light source vertical irradiation light to the code disk image onto the receiving on the surface. Receiver is covered with a diffraction grating, which has the same code disk window width. The receiver's job is to feel the rotation of the disc resulting changes, and change the light into corresponding electrical changes. Then the low-level signals up to a higher level, and generates no interference square pulse, which must be processed by electronic circuits. Reading systems typically employ a differential manner, about the same but the phase difference of the two waveforms different by 180°compared to the signal in order to improve the quality and stability of the output signal. Reading is then the difference between the two signals formed on the basis,thus eliminating the interference.